Combined trolley blast chiller and deep-freezing cell 160kg CC160

Description

Technical specifications

Reduced floor space
Stainless steel on all sides (including back, bottom and top)
Curved interior angles
Insulation thickness 70mm
Hinges on the right (on the left as an option)
Key lock
Easy access to the evaporator without tools
With or without cooling unit
Door height = 1,950mm
Equipment delivered unassembled (assembled on request)
Direct drainage of condensation water or by coupling two tapping points on the appliance (back and side)
Stainless steel floor as standard (cooling model)
Insulated stainless steel flooring 18mm thick fitted as standard (combined version)
Fluid R452A or subcritical CO2
With air-driven or water-driven cooling unit
Version without cooling unit: supply of evaporator, regulator and pre-set expansion valve (except CO2)
Pump down solenoid valve, dryer, expansion valve and liquid sight glass are supplied for cooling unit delivered separately. The cooling unit is not charged, but the evaporator and unit are pressurised with nitrogen
CO2 cell evaporators are tested at 60 bar. It is the installer’s responsibility to ensure that the installation does not exceed this pressure
Supply voltage: – With cooling unit: 3-Phase 400 V+T+N / 50Hz – Without genset: Single-phase 230V+T / 50Hz Requires 20A power supply for combined model
Gradual increase in fan power at the start of the cycle to avoid water splashes

Available fluids: R452A or CO2 subcritical (other fluids on request)
Rack and trolley capacity: 2xGN1/1 or 1xGN2/1 or 1x400x600 or 1x600x800 SASA or 1xGN1/1 oven trolley
Single-access or through-access model

With or without cooling unit
All makes of trolley accepted: FRIMA/RATIONAL – MKN –
BONNET THIRODE – LAINOX – ANGELO PO – BOURGEOIS –
CONVOTHERM – UNOX – CAPIC

Electronic expansion valve – optimisation of cooling time // unit | Ref. DETELEC160 | €865
Hinges on the right – LARGE VOLUME 160kg // unitary | Ref. FGCS160 | €190
RJ45 socket (only available with PREMIUM control system) // unit | Ref. PRISERJ45 | €240
PREMIUM control system with USB included LARGE VOLUME // unit | Ref. RPREMIUM | €1,143
Insulated flooring 18mm thick – LARGE VOLUME cooling cell 160kg – single-access // unit | Ref. SOLISOLECS160S | €733
Insulated flooring 18mm thick – LARGE VOLUME cooling cell 160kg – through-access // unit | Ref. SOLISOLECS160T | €867
3-point probe – assembled (only available with PREMIUM control) // unit | Ref. KITSONDE3PTS | €677

Trolley for cooling and deep-freezing cell 400×600 – 20 levels of 77mm – without grid (W 544 x D 650 x H 1,775 mm) // unit | Ref. CHAPAT20N | €1,089
Trolley for cooling and deep-freezing cell 600×800 – 20 levels of 77mm – without grid (W 925 x D732 x H 1,795 mm) // unit | Ref. CHARIOT600X800 | €1,251
Trolley for cooling and deep-freezing cell GN1/1 – 20 levels of 77mm – without grid (W 454 x D 653 x H 1,785 mm) // unit | Ref. CHAM20N | €1,047
Trolley for cooling and deep-freezing cell GN2/1 – 20 levels of 77mm – without grid (W 659 x D 773 x H 1,785 mm) // unit | Ref. CHAG20N | €1,187

Reduced floor space
Stainless steel on all sides (including back, bottom and top)
Curved interior angles
Insulation thickness 70mm
Hinges on the right (on the left as an option)
Key lock
Easy access to the evaporator without tools
With or without cooling unit
Equipment delivered unassembled (assembled on request)
Direct drainage of condensation water or by coupling two tapping points on the appliance (back and side)
Stainless steel floor as standard (cooling model)
Insulated stainless steel flooring 18mm thick fitted as standard (combined version)
Fluid R452A or subcritical CO2
With air-driven or water-driven cooling unit
Version without cooling unit: supply of evaporator, regulator and pre-set expansion valve (except CO2)
Pump down solenoid valve, dryer, expansion valve and liquid sight glass are supplied for cooling generator delivered separately. The cooling unit is not charged, but the evaporator and generator are pressurised with nitrogen
CO2 cell evaporators are tested at 60 bar. It is the installer’s responsibility to ensure that the installation does not exceed this pressure
Supply voltage: – With cooling unit: 3-Phase 400 V+T+N / 50Hz – Without cooling unit: Single-phase 230V+T / 50Hz Requires 20A power supply for combined model
Gradual increase in fan power at the start of the cycle to avoid water splashes</>

For more information, download the data sheet:

Shop